Artnet2DmxRecorder/lib/M5Stack/examples/Modules/GoPLUS2/GoPLUS2.ino

/*
    Description: Use GoPLUS Module for four-channel servo test and three-channel
   ADC test.
*/
#include <M5Stack.h>
#include <Wire.h>
#include <driver/rmt.h>
#include <math.h>

#include "GoPlus2.h"

GoPlus2 goPlus;

#define X_LOCAL 40
#define Y_LOCAL 30

#define X_OFFSET                160
#define Y_OFFSET                23
#define rrmt_item32_timemout_us 9500

int _hub1, hub1 = 0;
rmt_item32_t signals[1024];

size_t received = 0;

int flag = 0;
int num  = 0;

void header(const char *string, uint16_t color) {
    M5.Lcd.fillScreen(color);
    M5.Lcd.setTextSize(1);
    M5.Lcd.setTextColor(TFT_WHITE, TFT_BLACK);
    M5.Lcd.fillRect(0, 0, 320, 30, TFT_BLACK);
    M5.Lcd.setTextDatum(TC_DATUM);
    M5.Lcd.drawString(string, 160, 3, 4);
}

void Motor() {
    while (num == 0) {
        M5.Lcd.fillRect(0, 40, 320, 100, TFT_BLACK);
        M5.Lcd.setCursor(20, 40, 4);
        M5.Lcd.println("Motor Test");
        M5.Lcd.setCursor(20, 60, 4);
        M5.Lcd.println("Motor Speed: -127");
        goPlus.Motor_write_speed(MOTOR_NUM1, -127);
        goPlus.Motor_write_speed(MOTOR_NUM0, -127);
        delay(1000);
        goPlus.Motor_write_speed(MOTOR_NUM1, 0);
        goPlus.Motor_write_speed(MOTOR_NUM0, 0);
        delay(1000);
        M5.Lcd.fillRect(0, 60, 320, 180, TFT_BLACK);
        M5.Lcd.setCursor(20, 60, 4);
        M5.Lcd.println("Motor Speed: 127");
        goPlus.Motor_write_speed(MOTOR_NUM1, 127);
        goPlus.Motor_write_speed(MOTOR_NUM0, 127);
        delay(1000);
        goPlus.Motor_write_speed(MOTOR_NUM1, 0);
        goPlus.Motor_write_speed(MOTOR_NUM0, 0);
        delay(1000);
    }
}

void Servo() {
    while (num == 1) {
        M5.Lcd.fillRect(0, 40, 320, 100, TFT_BLACK);
        M5.Lcd.setCursor(20, 40, 4);
        M5.Lcd.println("Servo Test");
        M5.Lcd.setCursor(20, 60, 4);
        M5.Lcd.println("Servo Angle: 0");
        goPlus.Servo_write_angle(SERVO_NUM0, 0);
        goPlus.Servo_write_angle(SERVO_NUM1, 0);
        goPlus.Servo_write_angle(SERVO_NUM2, 0);
        goPlus.Servo_write_angle(SERVO_NUM3, 0);
        delay(1000);
        M5.Lcd.fillRect(0, 60, 320, 100, TFT_BLACK);
        M5.Lcd.setCursor(20, 60, 4);
        M5.Lcd.println("Pluse Width: 2000");
        goPlus.Servo_write_plusewidth(SERVO_NUM0_PW, 2500);
        goPlus.Servo_write_plusewidth(SERVO_NUM1_PW, 2500);
        goPlus.Servo_write_plusewidth(SERVO_NUM2_PW, 2500);
        goPlus.Servo_write_plusewidth(SERVO_NUM3_PW, 2500);
        delay(1000);
    }
}

void Port_B() {
    M5.Lcd.fillRect(0, 40, 320, 100, TFT_BLACK);
    while (num == 2) {
        M5.Lcd.setCursor(0, 40, 4);
        hub1 = goPlus.hub1_a_read_value(HUB1_R_ADDR);
        if (abs(hub1 - _hub1) > 3) {
            M5.Lcd.fillRect(160, 40, 70, 20, TFT_BLACK);
        }
        _hub1 = hub1;
        M5.Lcd.printf("HUB1 Analog: %d \r\n", hub1);
        int hub2 = goPlus.hub2_d_read_value(HUB2_R_O_ADDR);
        M5.Lcd.printf("HUB2 Digital: %d\r\n", hub2);
        if (M5.BtnC.wasPressed()) {
            flag = !flag;
            goPlus.hub3_wire_value(HUB3_W_ADDR, flag);
        }
        M5.update();
        M5.Lcd.printf("HUB3 State: %d\r\n", flag);
    }
}

void rx_channel_init() {
    rmt_config_t rmt_rx;
    rmt_rx.channel                       = RMT_CHANNEL_0;
    rmt_rx.gpio_num                      = GPIO_NUM_35;
    rmt_rx.clk_div                       = 80;
    rmt_rx.mem_block_num                 = 4;
    rmt_rx.rmt_mode                      = RMT_MODE_RX;
    rmt_rx.rx_config.filter_en           = false;
    rmt_rx.rx_config.filter_ticks_thresh = 0;
    rmt_rx.rx_config.idle_threshold      = 5000;

    rmt_config(&rmt_rx);
    rmt_driver_install(rmt_rx.channel, 1000, 0);
}

void tx_channel_init() {
    rmt_config_t rmt_tx;
    rmt_tx.rmt_mode                       = RMT_MODE_TX;
    rmt_tx.channel                        = RMT_CHANNEL_4;
    rmt_tx.gpio_num                       = GPIO_NUM_5;
    rmt_tx.mem_block_num                  = 4;
    rmt_tx.clk_div                        = 80;
    rmt_tx.tx_config.loop_en              = false;
    rmt_tx.tx_config.carrier_duty_percent = 50;
    rmt_tx.tx_config.carrier_freq_hz      = 38000;
    rmt_tx.tx_config.carrier_level        = RMT_CARRIER_LEVEL_HIGH;
    rmt_tx.tx_config.carrier_en           = 1;
    rmt_tx.tx_config.idle_level           = RMT_IDLE_LEVEL_LOW;
    rmt_tx.tx_config.idle_output_en       = true;
    rmt_config(&rmt_tx);
    rmt_driver_install(rmt_tx.channel, 0, 0);
}

void rmt_rx_task() {
    RingbufHandle_t rb = NULL;
    rmt_get_ringbuf_handle(RMT_CHANNEL_0, &rb);
    rmt_rx_start(RMT_CHANNEL_0, 1);

    size_t rx_size = 0;
    M5.Lcd.setCursor(20, 40, 4);
    M5.Lcd.println("wait ir signal...");
    rmt_item32_t *item = (rmt_item32_t *)xRingbufferReceive(rb, &rx_size, 3000);
    rmt_rx_stop(RMT_CHANNEL_0);
    if (!item) {
        M5.Lcd.println("no data received");
        return;
    }
    M5.Lcd.print("received items: ");
    M5.Lcd.println(rx_size);

    memcpy(signals, item, sizeof(rmt_item32_t) * rx_size);
    for (int i = 0; i < rx_size; ++i) {
        signals[i].level0 = ~signals[i].level0;
        signals[i].level1 = ~signals[i].level1;
    }
    received = rx_size;
    vRingbufferReturnItem(rb, (void *)item);
    M5.Lcd.println("recv done");
    rmt_rx_stop(RMT_CHANNEL_0);
    rmt_tx_task();
}

void rmt_tx_task() {
    M5.Lcd.println("send...");
    M5.Lcd.println(received);
    rmt_write_items(RMT_CHANNEL_4, signals, received, false);
    rmt_wait_tx_done(RMT_CHANNEL_4, 2000);
    M5.Lcd.println("send done");
}

void IR() {
    while (num == 3) {
        M5.Lcd.fillRect(0, 40, 320, 200, TFT_BLACK);
        rmt_rx_task();
    }
}

void doTask() {
    if (num == 4) {
        num = 0;
    } else {
        num++;
    }
    Serial.println(num);
}

void setup() {
    M5.begin();
    goPlus.begin();
    delay(100);
    rx_channel_init();
    tx_channel_init();

    //   goPlus.hub1_set_io(HUB1_R_O_ADDR, 1); //set digital_output to
    //   digital_input goPlus.hub2_set_io(HUB2_R_O_ADDR, 1); //set
    //   digital_output to digital_input goPlus.hub3_set_io(HUB3_R_O_ADDR, 1);
    //   //set digital_output to digital_input

    header("GoPlus 2", TFT_BLACK);
    M5.Lcd.setTextColor(TFT_GREEN, TFT_BLACK);
    attachInterrupt(digitalPinToInterrupt(38), doTask, RISING);
}

void loop() {
    Servo();
    Motor();
    Port_B();
    IR();

    //    int val1 = goPlus.hub1_d_o_read_value(HUB1_R_O_ADDR);  //read
    //    digtial_input int val2 = goPlus.hub2_d_o_read_value(HUB2_R_O_ADDR);
    //    //read digtial_input int val3 =
    //    goPlus.hub3_d_o_read_value(HUB3_R_O_ADDR);  //read digtial_input
    //    Serial.println(val1);
    //    Serial.println(val2);
    //    Serial.println(val3);
}